What
Makes Process Process?
Featured Author - Olin Thompson
- September
21, 2000
Introduction
Free Software Comparison
For a fast, free comparison of business software solutions best suited to your organization's needs, click below to visit TEC's Software Evaluation Center.
|
|
|
|
|
|
|
|
|
 |
| Rate this article |
| - |
|
 |
|
+ 0
|
|
|
|
Article has not been rated
|
|
|
|
An ERP or SCM solution has to be selected. The project holds significant
value. One way not to deliver on that value is selecting a vendor whose
product does not fit the needs of the business. This is common sense,
but for process companies, it can be particularly challenging. Process
companies, including food, chemical, pharmaceutical, forest products and
others, often have unique requirements not addressed by most technology
providers.
Not
all areas of technology reflect the uniqueness of a process business.
While financial systems have few requirements not in common with all companies,
operational systems often have many issues. The systems dealing with manufacturing,
inventory, procurement and customer order management systems are among
the systems that often prove to be the hardest to acquire due to the unique
issues of the process enterprise.
Although
the list of unique requirements can be defined, what are the root causes
of the differences … what makes process process? These root causes flow
from a few characteristics of the business.
The
Basic Nature of Material
Process materials are often powder, liquid, or gas on the raw material
end -- and either the same (industrial companies) or cases of product
(consumer goods companies) on the finished product end. The system must
allow you to measure and store these types of materials.
Measurement
of process materials is often done differently at various locations across
a single plant or supply chain. The units of measure (UOM) used vary even
when measuring a single material. Therefore, the product must allow any
UOM to be used anytime with the system automatically making all changes
to the standard unit of measure. For example, tons have to be converted
into pounds, gallons into kilograms, cubic feet into pounds or (for a
tank or silo) feet into gallons.
Process
materials change with time. They may get worse, they may get better or
they may become a different material. Discrete oriented systems assume
that materials do not change. A process solution must recognize and manage
the change of the material over time. For example, if a material deteriorates
over time, the Available to Promise (ATP) calculation should not consider
the material available after the shelf life date. Conversely, if the material
improves with time (aging) ATP should not start considering the material
until after the aging date.
Variability
A discrete manufacturer experiences relatively few surprises. They order
500 part A's from a vendor and he delivers 500, and parts either pass
or fail to meet the spec. Since parts are all the same, they do not need
to be segregated (no lot control requirement). Part A always fits with
part B and together they always make sub-assembly C. When they set out
to make 100 C's they almost always get 100 C's. If not, they have 98 C's
and 2 scrapped C's.
Contrast
this to the lack of predictability inherent in a process manufacturing
company. You specify 5000 pounds of material X with a range of acceptable
spec. The vendor delivers approximately 5000 pounds, but usually not exactly
that amount. You need to test the material to see if it meets your spec
and record what that spec is so you can utilize it correctly in satisfying
production or customer demand (maybe blending it off or standardizing
it if it is at the extreme end of the range). Since each shipment is a
slightly different quality, you need to segregate shipments (lot control)
to allow you to manage these differences. The formula says 100 pounds
of A plus 100 pounds of B makes 190 pounds of C. But each time you produce
C, you get a slightly different amount (yield loss or gain). Sometimes,
you do not get C -- but you do get a product that is close to C that is
called D. You cannot always predict all this but you must react to it.
Your
ERP system must allow you to plan for, react to and account for this lack
of predictability in both quality and quantity.
The
Process - Bill Shape
The primary determinant of the ability of a system to meet the production
management needs of a process company is in the model of the process.
If the model, as represented in the database is flawed, no amount of programming
can make the system provide for these requirements. Where do these errors
and problems surface? Typically, these problems arise in planning, scheduling
and costing.
The
classic Bill of Material application models a set of assumptions that
are very valid for the discrete company. One of these assumptions is that
many items (parts) make one end item. Since Bills are always drawn with
the consumed parts at the bottom and the produced part at the top, the
Bill of Material has a basic "A" shape. Outside of the discrete industries,
other bill shapes exist. For example, a poultry processor or a refinery
has a "V" shaped bill -- one item is processed into many items (i.e.,
a chicken is cut up and sold in many parts, breast, legs, thighs, etc.)
Process
manufacturers use multiple formulas for the same end item to account for
differences in raw material specifications, available, cost or process
variation (cooker one versus cooker two for example.) Most Bill of Material
based systems assume that the product is always made the same way and
therefore do not adequately address this issue.
If
your realities match the assumptions inherent in a Bill of Material, then
many ERP systems can work for you. If your realities do not match -- a
system based upon a Bill of Material (even if it is called a "formula"
in the sales pitch) needs very close inspection to see if it meets your
requirements.
Vendor
Approaches
How a software vendor addresses the needs of process companies falls into
one of three categories:
- A few
vendors never mention process. By default, they are stating that they
do not address the needs of process companies.
- Many
vendors started with a discrete ERP or SCM product and later decided
to market it as a product suitable for process industries. These vendors
and products can easily be identified because they typically have a
module that includes the word "process". This add-on module is where
they attempt to address the characteristics and requirements that make
their discrete product into one for process.
- A few
vendors started with a strategy that focused exclusively on process.
These vendors do not have a process module; the entire product is designed
to address the particular requirements of process companies and only
process companies.
How can you
tell which vendor falls into which category? The first rule is, do not
listen to the sales pitch about "process focus". A simple test is to look
at the vendor's web page. This is a generalized message to the market
that tells you what the vendor is really trying to accomplish. Where is
process discussed? Is it the focus of the first page or is it listed as
one of many "areas of focus" on page 12 of the web site?
Look at the
annual report. What percentage of the customers listed are process? What
industries does the company say they serve? When they talk about specific
customers, do they talk about companies who are in your business? When
the vendor does have process customers, what did these customers install
from that vendor? Perhaps a vendor has many process companies, but most
or all of them installed financials. Few, if any, have installed the vendor's
software for operational functions. This may mean that the vendor is an
excellent financials vendor, but can the vendor handle your operational
needs?
What
Do You Need?
If you are in the market looking for financials, many products can do
the job. The industry focus of the vendor is not critical. If you are
looking for operational functions or supply chain functions, then the
focus and approach of the vendor is very meaningful.
How
process are you? Some process companies have relatively simple processes
(receive bulk materials, mix and package) and deal with materials that
are very consistent. These companies can be called "simple process". For
these companies, any P-ERP should be considered. Even the ERP products
that have been extended from discrete products can often do the job.
Companies
with more complex process business requirements have a different challenge.
If they choose to look at the companies that have taken the add-on approach,
they must look in detail at the process functions they need to run the
business. Typical problem areas include the full management (planning,
execution and analysis/costing) of process with by-products, co-products
and recycles and management of inventories to solve customer and production
requirements. A second area is the ability of the system to fully define
your inventory at the level you need to achieve high levels of customer
satisfaction.
For
these complex process companies, the vendors who devote themselves exclusively
to process bear a closer look. You should expect them to do a better job
of modeling and managing your reality.
The
Cost of Picking the Wrong Product
What is the cost of picking the wrong product? The cost of picking the
wrong General Ledger product is important to the CFO's office and hinders
your ability to do a complete analysis of the financial side of the business.
Picking operational systems that do not give operational management the
tools they need means a choice. The first choice: you can "make do" with
inferior management tools resulting in potentially poor business decisions.
The second choice: you can build work-arounds or custom solutions on top
of the ERP solution, resulting in a large investment of both time and
money - initially, and as part of your long-term cost of ownership.
About
the Author
Olin Thompson
For
over 20 years, Olin Thompson has served as an executive with companies
providing application software and internet based solutions for the process
industries' supply chain. He has experience in general management, sales,
marketing, business development and business and product strategy. He
is a frequent contributor to industry magazines and journals, an award
winning public speaker and has been called the father of Process ERP.
|
